Видео

Thank you, God bless

thanks Chuck!

What is the thickness of your door?

Great Step By Step instructions but, you should have shown us 'Before and After" results.

What is the part kit number for the water valve you changed out last please?

Where did you order your waste ball drive arm from? Your video is the only one we have found that is so self explanatory so thank you!

My 2006 FW Bounder is an F53 with a reman 2015 V10 so I do use the oil filter bag hack and will get BOUNDER a fumitomo oil drain valve! Your style and video is Crystal Clear - and as a retired teacher I respect that!! When / how often do you do trans oil & filter? TIA

Thanks 😊

On my LCI Power Gear jacks (2015) the jacks retract fully with one touch of the button. I wish I could control the amount of retraction like yours for leveling adjustments.

One hell of a hot day

This is a very detailed illustration. Thank you for taking the time to do this for us. I can't wait to start on mine.

Excellent video, I finally got a normal softie, changing from the fastback NX top that I’ve had on for 9 years. IE I’ve never had the bow frame. Excellent how to video!

Awesome- just what I was looking for. Thank-you!

The pass-thru holes seem large enough for mice to get in past the tubing hanging down. Maybe pack the space with steel wool to close the gap.

Thanks for your content •••

These toilets leak if the water pressure in the RV park is low. They can't seal with low pressure. Someone at Thetford who builds these said so. Thetford mostly won't admit it to you though. Ours flooded twice due to low pressure in the park. We did change all parts but if pressure in park is low, it still starts dripping--loses its seal. I just turn off water each day as I leave for work. Not going to chance it and clean up a flood again!! Why can't they engineer these differently? The 1970s version with a slide bottom was a much better design.

There are lots of videos on this subject. Yours is by far the easiest to understand especially with these pics and videos of the process. Luckily you have a professional videographer to work with…the Mrs)she knows what to show and gets the camera in the right place

Thank you for the great video

Followed step by step…everything that clicked clicked, everything that snapped, snapped, all o rings got lubricated, an new gaskets, but now the new waste ball does not close all the way by itself, so, obviously does not hold water 😭☹️🥵

Thank you

great video thank you

Ordered one today, thank you.

My thought is the Pex you get at Home Depot is different than the Pex you get at an RV parts store ??

I am changing out my water pump using the fittings that came with my Shurflo pump. I have to remove the existing fittings as they are different. After inserting the new fitting into the pex the pex clamp will not fit over the fitting burr, what the issue?.

Nice video. Straight to the point and very helpful. Thanks.

WoW thank you very much

I can't thank you enough for providing such clear and thorough videos of these proceedures. I purchased the fuel filter, the oil filter, the oil filter wrench and the oil pan valve off the links you provided. Pumped to do this maintenance and keep our Onan 5500 running like it should!

aug 2024. great job making it look eazy. here I go. one handle to install. thanks again.

My last couple of RV’s were all PVC. Don’t recall seeing any copper.

Will this work for a 2011 Jeep Compass

Do your universal joints not have zerks? My diesel does and they can be a bear to get at. on my joke, I need to add grease until it starts to come out of the weep hole in the U-joint end of the yoke. Then you cover the weep hole with your finger and pump until fresh grease comes out the spline seal.

I lay a 2 foot long piece of aluminum foil lengthwise over the I beam and then remove and discard it after I put the oil plug back in. No mess. I also puncture the bottom of the old filter with a sheet rock nail to let it drain while I take a break. On filling I use small mouth oil bottles. No spillage. Also I put a 2 inch diameter white styrofoam doughnut over the end of the oil filler tube so I can always see where to aim the dipstick.

Does a 20 pound propane need a regulator I’m asking because I purchased a kit like this and tried it and no gas was getting into the RV tank

Thank you for your video. We are newbies to class a. I have been wanting to try manually leveling our rig. However we have just been using aito level. 99% of our campsites (so far) are pretty close to being level. I must be doing something wrong when we get ready to leave. I start Stormy to run in the slide first but she drops 🤔 what am I doing wrong? I am afraid this can not be good for the slide? After watching this video I am wondering if I did not shut the level off. Should I shut it off while the engine is still running?

Hi 👋

Shouldn’t U change the value to Brass.

I think I found an easy way too. I use a paint roller pan with a hole in the end of it. Also I use a pump from harbor freight for 5 gallon cans to pump the oil from 5qt bottles. The roller pan also works for the oil filter. Just make sure your catch pan under the roller pan is centered. My first mistake. The metal roller pan has feet that catch perfectly on the torsion bar to hold it in place so it won't fall down on you. Hope this helps someone. See the pictures.

Hello, Could you please explain what type of USB drive you use for download. I was told not to use SanDisk PNY. (I tried oon usb, but make sure it's a Fat32 Formatted) .. I downloaded file off computer, stuck drive into my 2016 Jeep Cherokee Limited. It say's ... Files Not Supported ... HELP!!

We're do u get the spring for screen door handel

Your video is very informative, in very detailed. You mentioned level mate pro device. Please send me the link how to install it that also shows what location it is to be installed. Thanks.

Hi

Do they have ice cubes in hell?

Thanks for the videos!! We had major issues where we were online with Lippert Service and what they had us do ended up breaking a pin. Then, once we fixed the pin we tried to manually (the nut on the jacks) lower the jack and found the front right was binding. Ordered a new motor/gear box and reinstalled everything and all seems to be good now!! We like to sit a little nose down when running air conditioning so it runs off the front. In the process, we also ordered a new control pad since our Bounder is a 2007. It has been an ordeal and we are in our 70’s, so we really appreciated watching your videos!! Blessings on you.

Fantastic video! I followed you all the way but see no spark on wires showing a bad wire still won’t lite but did yesterday. 😢

I just got home from vacation and leveled out our RV on our gravel driveway. After putting boards on 3 of the 4 tires to get it level using a 4 foot level. I then reset the leveler like you said and bam it was perfect! Your guys are awesome and thanks to you tube making everyone’s life easier with people like you. Thank you!!

Awesome video.

Thanks. I am having that same problem with my canopy on my Palomino Paomini and glad I came across this video. Adding a little Loctite to those screws with help in making sure they don’t come loose. Thanks again

How to make sure the gas going through

You seem to be a big TT supporter, which is fine. But, full disclosure would be nice of perks you may get in return.

Great video you two!